After changing to yahoo asia , POP3 work! SMTP dont work??

[kofv]

I did all as guys following :
need startlls or tls
my steps:
Sign in at the main (not mail) Yahoo page (http://www.yahoo.com)
On the top right, where it says "Hi <yourname>", click on <yourname>
Enter the requested password
Edit "Member Information" (first choice)
Select "Preferred Content", and change it to "Yahoo Asia"
Click Finished and Accept the Terms
Select Finished again
Sign Out

When you sign back in to Yahoo Mail (http://mail.yahoo.com), you will now see the "Yahoo Asia" logo
Select Options (near the top right)
You will now have a "POP3 Access and Forwarding" choice under Management

I used becky 2.5
When I set to yahoo asia as following
(POP3): pop.mail.yahoo.com
Use SSL, port: 995
(SMTP): smtp.mail.yahoo.com
Use SSL, port: 465, use authentication

it fail ,but I switch the port back to 110, 25 (with pop port and smtp port as said upstairs) It can receive and can not send , at least I did not need to use freepops till now .

so I try seperate POP in default , and try SMTP in 4 statuses
default, startlls, over tls 1.0, over lls 2.0, over lls 3.0, but all fail ( port 465)
all fail .

when sending , It said 530 auth...required.
or there is a communicating problem . can anyone else can help?

[anujseth]

Please refer to my post on the 0.9.7 status.

[dbeusee]

did you actually click on "POP3 Access and Forwarding" and actually enable it?

-Don

I did all as guys following :
need startlls or tls
my steps:
Sign in at the main (not mail) Yahoo page (http://www.yahoo.com)
On the top right, where it says "Hi <yourname>", click on <yourname>
Enter the requested password
Edit "Member Information" (first choice)
Select "Preferred Content", and change it to "Yahoo Asia"
Click Finished and Accept the Terms
Select Finished again
Sign Out

When you sign back in to Yahoo Mail (http://mail.yahoo.com), you will now see the "Yahoo Asia" logo
Select Options (near the top right)
You will now have a "POP3 Access and Forwarding" choice under Management

I used becky 2.5
When I set to yahoo asia as following
(POP3): pop.mail.yahoo.com
Use SSL, port: 995
(SMTP): smtp.mail.yahoo.com
Use SSL, port: 465, use authentication

it fail ,but I switch the port back to 110, 25 (with pop port and smtp port as said upstairs) It can receive and can not send , at least I did not need to use freepops till now .

so I try seperate POP in default , and try SMTP in 4 statuses
default, startlls, over tls 1.0, over lls 2.0, over lls 3.0, but all fail ( port 465)
all fail .

when sending , It said 530 auth...required.
or there is a communicating problem . can anyone else can help?

[chubby22]

Did you check the button that says my outgoing server requires authentication. Use same settings as my incoming mail.

[kofv]

Did you check the button that says my outgoing server requires authentication. Use same settings as my incoming mail.

yes I did . Thanks for reminding




did you actually click on "POP3 Access and Forwarding" and actually enable it?

-Don

yes, I did , If I didnt enable it , at least , it wont receive emails. POPS is about receiving , SMTP ( SIMPLE MAIL TRANSFER PROTOCAL) is about sending.
I am not a newbie , and I checked all for more than 5 times .I think maybe account different
I registered this account in 2004.

Thanks any way .

[chrisretusn]

I used becky 2.5
When I set to yahoo asia as following
(POP3): pop.mail.yahoo.com
Use SSL, port: 995
(SMTP): smtp.mail.yahoo.com
Use SSL, port: 465, use authentication

when sending , It said 530 auth...required.
or there is a communicating problem . can anyone else can help?

You problem sounds to me like you have not entered your SMTP Authentication informations (full e-mail and password). Account properties, Misc tab in Becky. Click SMTP Auth and for User ID: enter [email protected]; then your password. That should solve your problem. Make sure your setup is as stated above.